RESEARCH PAPER
Deformation Properties of Tailor Welded Blank Made of Dual Phase Steels
1
Faculty of Mechanical Engineering, Slovak University of Technology in Bratislava, Institute of Technologies and Materials, Pionierska 15, 831 02 Bratislava, Slovakia
Submission date: 2015-11-02
Acceptance date: 2016-02-22
Online publication date: 2016-03-07
Publication date: 2016-03-01
Acta Mechanica et Automatica 2016;10(1):38-42
KEYWORDS
ABSTRACT
The paper is dedicated to forming and properties of passenger car’s B-pillar reinforcement drawn from simple blank and alternatively tailor-welded blank (TWB). Drawn part is characterised by a place with a large strain, while forming process simulation did not confirm the creation of crack using the TWB consisting of dual phase HCT980X instead of previous HCT600 steel. It is because HCT980X steel has higher strength and lower ductile properties. The analysis of properties of drawn parts is focused on the simulated crash test in Dynaform software. Obtained sizes of drawn forces in simulated frame of the drawn parts and their comparison proved the possibility of the replacement the 1.2 mm thick simple blank from HCT600 steel with the 1 mm thick TWB consisting of HCT600 and HCT980X steel. The changed thickness of the simple blank caused 20% weight saving while containing the same properties of the drawn part.
REFERENCES (18)
1.
Bílik J., Balážová M., Kršiaková Ľ., Šuba R. (2010), The analyssis of properties and forming duplex steel DP 450, Hutnícke listy, Vol. 63, No. 4, 74-77.
2.
Bílik J., Ertel J., Bárta J., Marônek M., Šugárová J. (2015), The analyssis of properties and forming of laser welded superduplex steel SAF 2507, Hutnik-WH, Vol. 82, No. 9, 627-631.
3.
Chena, W., Linb, G.,S., Hub, S.,J. (2008), A comparison study on the effectiveness of stepped binder and weld line clamping pins on formability improvement for tailor-welded blanks, Journal of materials processing technology 207, 204-210.
4.
Daxin E., Takaji M., Zhiguo L. (2008), Stress analysis of rectangular cup drawing, Journal of Materials Processing Technology, Vol. 205, 469-476.
5.
Evin E. (2013), Design of dual phase high strength steels sheet for auto body, Metal 22nd International Conference on Metallurgy and Materials, Conference Proceedings.
6.
Evin E., Antoszewski B., Tomáš M., Tkáčová J., Draganovská D. (2015), Tribological Properties of Coatings for Sheet Metal Stamping Dies, Materials Science Forum, Vol. 818, 69-73.
7.
Evin E., Tomáš M. (2012), Comparison of deformation properties of steel sheets for car body parts, Procedia Engineering, Vol. 48, 115–122.
8.
Fracz W., Stachowicz F., Pieja T. (2013) Aspects of verification and optimization of sheet metal numerical simulations process using the photogrammetric system, Acta Metallurgica Slovaca, Vol. 19, 51-59.
9.
Fracz W., Stachowicz F., Trzepiecinski T., Pieja T. (2014), Forming limit of the heat resistant AMS 5599 sheet metal, Hutnik-WH, Vol. 81, No. 7, 442-445.
10.
Groche P., Metz C. (2006), Investigation of active-elastic blank holder systems for high-pressure forming of metal sheets, International Journal of Machine Tools & Manufacture, Vol. 46, 1271-1275.
11.
Kinsey L.B., Wu X. (2011), Tailor-welded blanks for advanced manufacturing. Woodhead publishing, Cambridge.
12.
Merklein M., Johanes M., Lechner M., Kuppert A. (2014), A review on tailored blanks – Production, applications and evaluation, Journal of Materials Processing Technology, Vol. 214, 151-164.
13.
Padmanabhan R., Baptista A.J., Olivieira M.C., Menezes L.F. (2007), Effect of anisotropy on the deep-drawing of mild steel and dual-phase steel tailor-welded blanks, Journal of Materials Processing Technology, Vol. 184, 288-293.
14.
Reisgen U., Schleser M., Mokrov O., Ahmed E. (2010), Uni- and bi-axial deformation behavior of laser welded advanced high strength steel sheets, Journal of Materials Processing Technology, Vol. 210, 2188-2196.
15.
Reisgen U., Schleser M., Mokrov O., Ahmedn E. (2012), Statistical modelling of laser welding of DP/TRIP steel sheets, Optics & Laser Technology, Vol. 44, 92-101.
16.
Sinha, A.K., Kim, D.Y., Ceglarek, D. (2013), Correlation analysis of the variation of weld seam and tensile strength in laser welding galvanized steel, Optics and Laser in Engineering, 51, 1143-1152.
17.
Slota J., Jurčišin M., Spišák E. (2014), Experimental and numerical analysis of local mechanical properties of drawn part, Key Engineering Materials, Vol. 586, 245-248.
18.
Zhong-Qin L., Wu-Rong W., Guan-Long C. (2007), A new strategy to optimize variable blank holder force towards improving the forming limits of aluminum sheet metal forming, Journal of Materials Processing Technology, Vol. 183, 339-346.
| eISSN: | 2300-5319 |
| ISSN: | 1898-4088 |
We process personal data collected when visiting the website. The function of obtaining information about users and their behavior is carried out by voluntarily entered information in forms and saving cookies in end devices. Data, including cookies, are used to provide services, improve the user experience and to analyze the traffic in accordance with the Privacy policy. Data are also collected and processed by Google Analytics tool (more).
You can change cookies settings in your browser. Restricted use of cookies in the browser configuration may affect some functionalities of the website.
You can change cookies settings in your browser. Restricted use of cookies in the browser configuration may affect some functionalities of the website.
